火石模组全自动预供芯片 FireStoneModule Automatic Pre-Load

We use machine translate for this page and may not be accurate.

You can buy our prodect on this url:https://item.taobao.com/item.htm?id=611380758134&ns=1&abbucket=7#detail

Learn how buy on Taobao :https://blog.seedly.sg/step-by-step-guide-how-to-shop-on-taobao-chinese/

如果您想进行商务合作,在您的店铺代理销售本产品,请在文章下方留言您的联系方式,我们会主动与您联系

If you want to do business cooperation and sell this product in your shop, please leave your contact information below the article, we will contact you proactively

二极管可能和模组连接在一起,请用用钳子轻轻掰下即可)
The diode may be connected to the module, please use the pliers to lightly press down)

激趣/任翔波的注意事项 Note for LDT gearbox:

    激趣波箱的线路和锦明波箱的线路不一样(激趣波箱的扳机接在电源的正极,锦明波箱的扳机接在电源的负极上)
    需要将激趣波的接线改成锦明波的接线方式才能正常使用
LDT use switch controls VCC ,you need change the switch controls GND ,then use it.

激趣/任翔波的更改方法如下:

    激趣波需要将原装线路的 电源插头中的端子取出,然后正负对调,对调将两个弹簧位置交换后,才能按照教程接线。(注意线路对调后,电机红点对应原本的黑色插头)

注意事项 Note:

  1. 模组正负极不能反接,反接会导致模组损坏。The positive and negative terminals of the module cannot be reversely connected. Reverse connection may cause damage to the module.
  2. 使用时请不要用金属短路弹夹两个接触片。Please do not use metal short clips to clamp the two contact pieces during use.
  3. 长时间不使用发射器,请取下电池。Do not use the transmitter for a long time, please remove the battery.

产品特性 Product Features:

  • 采用第三代成熟架构稳定全自动预供
  • 无需更换原线组易于改装
  • 小体积可以轻松置入后托/机匣内部
  • 可以通过按钮调整预供弹时间
  • 兼容手动预供,兼容其他火控芯片

规格参数:

产品尺寸 size​ 11mm*28mm*7.5mm
电压范围 voltage range6.2V – 15V
过流/短路保护
Overcurrent / short circuit protection
 自带输出保护 yes
省电模式
Power saving mode
 闲置状态15分钟左右自动进入睡眠模式(拔下弹匣时7分钟左右)
Automatically enters sleep mode in about 15 minutes when idle (about 7 minutes when the magazine is removed)
预供调节时间
Pre-Load adjustment time
0.1s – 25s 调节幅度0.1s

设置按钮使用方法 How to use the setting button::

  • 默认预供时间为1s The default pre-load time is 1s
  • 短按为增加预供时间(高音一声)Short press to increase pre-load time (one high beep)
  • 长按为减小预供时间(低音一声)Long press to decrease the pre-load time (one low beep)
  • 长按响两声表示设置值已经为零 when long press beep twice, is mean the setting value is zero

(插弹夹时可听见设置音效,不插弹夹不会听到音效)

(You can hear the set sound effect when inserting the clip, you will not hear the sound effect without inserting the clip)